基于碳纳米管薄膜的复合材料层间增韧

通过浮动催化化学气相沉积法制备连续碳纳米管薄膜，并将其原位沉积到单向碳纤维织物表面，手工铺层后借助真空辅助树脂传递模塑成型（VARTM）工艺制备碳纳米管-碳纤维/环氧树脂复合材料层压板，研究不同面密度的碳纳米管薄膜对层压板Ⅱ型层间断裂韧性的影响。结果表明，随着碳纳米管薄膜面密度的增加，层压板Ⅱ型层间断裂韧性先逐渐提高，当碳纳米管薄膜面密度为9.64 g/m²时，层压板Ⅱ型层间断裂韧性最佳，与原始层压板相比提高了94%。碳纳米管通过桥接树脂裂纹、从树脂中拔出等方式提高层间断裂韧性。当碳纳米管面密度超过临界值时，会引起树脂浸润困难，导致增韧效果降低。     

涡轴发动机发展与技术趋势

首先,对美国20世纪70年代以来各时期涡轴发动机发展规划及其性能演变过程进行了梳理,并分析了不同循环类型及循环参数的选择,进行了性能统计分析。然后,介绍了直升机/发动机一体化设计理论的基础与方法。最后本文提出新一代超低排放涡轴发动机的概念,指出降低总耗油量的同时提高功重比,才能实现超低排放。     

新一代战斗机非定常流动数值研究综述

新一代战斗机强调超机动能力和强隐身性，其中大攻角下的静态失速、动态失速及内埋弹仓绕流是与高机动和强隐身密切相关的、极具挑战的几类典型的非定常流动，它们对数值方法提出了极高的要求。为了高精度地仿真流场、清楚地揭示流动机理，有效地控制非定常流动，非常有必要发展高精度且高效率的RANS-LES混合方法体系，包含RANS-LES混合方法本身、与RANS-LES混合方法匹配的高精度自适应耗散格式、基准湍流模式、高质量计算网格、高精度时间推进方法、非定常量的统计方法等，具有极强的紧迫性。提出、发展、验证并应用该类方法数值仿真新一代战斗机（包括单独部件、组合体、甚至全机）的非定常流动，数值预测结果与风洞实验数据吻合良好；此类方法可为新型战斗机设计提供理论依据和分析手段。     

热/力耦合作用下基于应力分析的冰破坏准则

根据飞机热除冰的物理过程,考虑外部空气动力和蒙皮表面加热的作用,建立了NACA 0012翼型前缘冰层应力计算模型。采用有限元方法和平面三角形单元对控制方程组进行了求解,获得了外部空气动力和蒙皮表面加热对冰层黏附界面应力的影响规律。研究表明:蒙皮表面不加热时,来流速度影响了黏附界面应力的强度,来流攻角影响了黏附界面应力的分布,冰-蒙皮间黏附界面切应力最大值随来流速度呈近似线性增大趋势,但外部空气动力很难造成冰层破坏。蒙皮表面加热时,冰-蒙皮间黏附界面的耦合应力和冰层内部的主应力随着热流密度的增大而增大,很容易超过剪切强度,这是造成冰破坏的关键因素。耦合冰-蒙皮剪切强度随界面温度的变化关系,初步建立了基于应力分析和热/力耦合作用的冰破坏判断准则。外部空气动力产生的界面应力和蒙皮表面加热产生的界面热应力之和，必须大于与蒙皮表面温度相关的剪切强度，则冰层发生破坏，破坏位置是耦合应力超过剪切强度的区域。      

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

A novel control method for turboshaft engine with variable rotor speed based on the Ngdot estimator through LQG/LTR and rotor predicted torque feedforward

In order to compensate for the disturbance of wide variation in rotor demanded torque on power turbine speed and realize the fast response control of turboshaft engine during variable rotor speed, a cascade PID control method based on the acceleration estimator of gas turbine speed (Ngdot) and rotor predicted torque feedforward is proposed. Firstly, a two-speed Dual Clutch Transmission (DCT) model is applied in the integrated rotor/turboshaft engine system to achieve variable rotor speed. Then, an online estimation method of Ngdot based on the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) is proposed for power turbine speed cascade control. Finally, according to the cascade PID controller based on Ngdot estimator, a rotor demanded torque predicted method based on the Min-batch Gradient Descent-Neural Network (MGD-NN) is put forward to compromise the influence of rotor torque interference. The simulation results show that compared with cascade PID controller based on Ngdot estimator and the one combined with collective pitch feedforward control, the novel control method proposed can reduce the overshoot of power turbine speed by more than 20%, which possesses faster response, superior dynamic effect and satisfactory robustness performance. The control method proposed can realize the fast response control of turboshaft engine with variable rotor speed better.     

Global ionospheric scintillations revealed by GPS radio occultation data with FY3C satellite before midnight during the March 2015 storm

Global observations of S4 amplitude scintillation index by the GPS Occultation Sounder (GNOS) on FengYun-3 C (FY3C) satellite reveal global dynamic patterns of a strong pre-midnight scintillations in F-region of the ionosphere during the St. Patrick’s Day geomagnetic super storm of 17–19 March 2015. The observed strong scintillations mainly occurred in the low latitudes, caused by equatorial plasma bubbles. During the main storm phase (March 17), the scintillations were first triggered in the New Zealand sector near 160°E longitudes, extending beyond 40°S dip latitude. They were also enhanced in the Indian sector, but significantly suppressed in East Asia near 120°E longitude and in Africa around 30°E longitude. During the initial recovery phase (March 18–19), the global scintillations were seldom observed in GNOS data. During the later recovery phase (after March 19), the scintillations recovered to the pre-storm level in Indian, African, and American sectors, but not in East Asian and any of Pacific sectors. These results closely correlate with observations of the density depletion structures by the Communication/Navigation Outage Forecasting System (C/NOFS) satellite, and ground-based instruments. Such consistency indicates reliability of our scintillation sensing approach even in a case-by-case comparison study. The prompt penetration electric field and disturbance dynamo electric field are suggested as the main factors that control the enhancement and inhibition of the scintillations during the storm, respectively.     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

边界层抽吸对超燃冲压发动机流场特性的影响研究

为了解边界层抽吸对超燃冲压发动机流场的影响,采用风洞试验和数值计算对隔离段激波串特性以及燃烧室燃烧特性进行了研究。结果表明,在发动机入口马赫数2.0,总温950K,总压0.82MPa的来流条件下,当量比为0.18先锋氢气与不同当量比煤油共同燃烧呈不稳定状态,激波串在隔离段内前后振荡传播。当煤油当量比为0.29时,激波串振荡前缘远离抽吸位置,边界层抽吸对发动机流场基本没有影响。随着煤油当量比逐渐增大,激波串前缘位置到达抽吸区附近,边界层抽吸开始产生影响,改变了隔离段内的激波串动态演化过程、形态结构以及位置分布,同时有效提高了隔离段抗反压特性,使得煤油最大当量比可以由0.38增大至0.42。此外,边界层抽吸对发动机内的亚燃/超燃区域分布也会产生影响。     

C/SiC材料主被动氧化烧蚀机理及计算方法研究

基于热化学平衡方法建立了任意比例C/SiC材料的主被动氧化烧蚀模型，开展了C/SiC材料氧化烧蚀机理的计算研究，并基于典型材料烧蚀试验结果进行了充分验证。计算结果表明，C/SiC材料的氧化烧蚀特性取决于表面温度、氧分压以及组分等因素，可能会出现主动氧化和被动氧化两种破坏机制，目前的烧蚀模型能够预测出任意比例C/SiC材料两种氧化烧蚀机制的转换过程；SiC含量对C/SiC材料的氧化烧蚀特性有明显的影响，随着SiC含量的提升，主/被动氧化转换临界分压会减小，材料的抗氧化性能越好；但当材料均处于主动氧化阶段时，SiC含量越高材料的无量纲烧蚀速率越大，材料的抗烧蚀性能减弱。